Selleys Storm Product

Hazard information for Storm Sealant

Storm Sealant carries the signal word Warning, with H317 (may cause an allergic skin reaction) and H319 (causes serious eye irritation).

Skin sensitisation (H317) is not irritation. Irritation settles when contact stops; sensitisation is the immune system learning to react, generally permanent once acquired, triggered thereafter by far smaller exposures, and built by repeated casual contact rather than one big exposure. That is why it matters on a product you use often.

The hazard-to-use mismatch on this product is worth stating plainly: Storm exists for emergency repair in the wet, which in practice means on a roof, in rain, possibly at night, often on a ladder. Those are precisely the conditions in which gloves and eye protection get skipped. If you are reaching for it in an emergency, it is still a sensitiser.

Storm also publishes very little technical data — Selleys issues a VOC certificate rather than a full data sheet — so movement capability, cure rate and service temperature are not available. The practical rule that follows: stop the leak with Storm, then reinstate the joint with a fully specified sealant once the roof is dry.

Selleys Storm products

This page lists the products in the Selleys Storm sealant range — sealants for protection against extreme weather, aimed at a durable, waterproof, long-lasting seal.

The product listing itself is generated on the live page. For what each product does, the materials and conditions it covers, and how to apply it, open the individual product you are interested in.

Where to go next

Directions, material compatibility and safety information are published on each individual product's page and label. Read the label of the specific product before use.

Define the joint before choosing the sealant

Identify every surface in contact with the sealant, including coatings, primers, backing materials and adjacent stone or metal. Record the joint width and depth, expected movement, indoor or outdoor exposure, water exposure, temperature and required appearance. These facts determine whether a general silicone, neutral-cure product, specialist glazing sealant, wet-area product or another system is appropriate.

Check cure type, adhesion requirements, tooling time, movement capability, paintability and excluded substrates on the exact product page. Do not treat elongation at break as a rated joint-movement figure. Water resistance, mould resistance and weather resistance also answer different questions and do not establish suitability for permanent immersion.

Plan removal, preparation and cure

  1. Remove old sealant and loose material without damaging the adjoining surfaces.
  2. Clean and dry the joint using only compatible preparation products.
  3. Use backing material and joint dimensions where the product instructions require them.
  4. Mask, apply and tool within the stated working time.
  5. Protect the bead from water, movement and service until the relevant cure milestone.

Verify specialist applications

Glazing, mirrors, natural stone, aquariums, drinking-water contact, structural joints and permanent immersion need explicit product coverage. Use the current Technical Data Sheet and Australian Safety Data Sheet for the supplied pack, and ask Selleys when the documentation does not establish compatibility.

What to check for your job

Compare the options: Selleys Storm Product

Use this category to create a shortlist, then compare the exact candidates in a simple job table. Record the materials, location, exposure, movement or load, required finish, working time, support or protection period, full cure and major exclusions. A shared category or brand name does not make the products interchangeable.

  1. Suitability: both substrates, coatings and service conditions.
  2. Application: preparation, tools, dimensions, coverage and working time.
  3. Waiting: support removal, water exposure, sanding, painting and full cure.
  4. Finish: colour, visibility, flexibility, paintability and clean-up.
  5. Evidence: the current pack, Technical Data Sheet and Australian Safety Data Sheet.

Open the individual page for every shortlisted product. Where this category contains a retained discontinued page, use it to identify older stock or work and confirm current availability or a replacement directly with us.

Complete joint-planning checklist for Selleys Storm Product

Record every adjoining material, coating and primer; the joint width and depth; expected movement; water, weather and temperature exposure; and the required colour, finish and paintability. Cure chemistry, substrate compatibility and joint geometry matter as much as the range name.

  1. Remove failed sealant and contamination without damaging the surrounding surface.
  2. Confirm whether primer, backing rod or a particular joint ratio is required.
  3. Plan masking, application and tooling within the published working time.
  4. Protect the bead from water, movement, dust and service during cure.
  5. Use the exact product documents for paint, immersion and maintenance limits.

Do not treat elongation at break as rated joint movement, or mould resistance as a promise of a maintenance-free joint. Aquariums, drinking water, natural stone, structural glazing and permanent immersion need explicit approval.

Details to check before you choose

More help for your project

Use these pages to compare the exact product, method or application that follows from Selleys Storm Product. A related page is a route into more specific information, not evidence that every product is interchangeable.

Can I disturb the seal as soon as it stops water?

No. Leave Storm undisturbed until cured, approximately 48 hours, even though it forms an immediate waterproof seal.

Can I use the Grey/Black movement figure for Clear?

No. Grey/Black lists ±20% movement and Clear ±12.5% under the stated modified ISO 9046 method. Use the data for your colour.

Can I apply Storm to a wet surface?

Storm is described for wet or dry surfaces, including rain, but its written preparation requires clean, dry surfaces. Ask our team for wet-application preparation if you cannot meet that requirement.

Can I paint it with solvent-based paint?

Not directly. Allow cure and use the colour-specific water-based exterior-paint directions first; Grey/Black requires two coats.

What should I know about hazard information for Storm Sealant?

Storm Sealant carries the signal word Warning , with H317 (may cause an allergic skin reaction) and H319 (causes serious eye irritation) . Skin sensitisation (H317) is not irritation. Irritation settles when contact stops; sensitisation is the immune system learning to react, generally permanent once acquired, triggered thereafter by far smaller exposures, and built by repeated casual contact rather than one big exposure.

What should I know about Selleys Storm products?

This page lists the products in the Selleys Storm sealant range — sealants for protection against extreme weather, aimed at a durable, waterproof, long-lasting seal. The product listing itself is generated on the live page. For what each product does, the materials and conditions it covers, and how to apply it, open the individual product you are interested in.

Where to go next?

Directions, material compatibility and safety information are published on each individual product's page and label. Read the label of the specific product before use. Selleys Storm in detail — what the range is for, and why it can be applied to wet surfaces and in the rain when conventional sealants cannot; Storm Sealant — our product page, with its own directions and pack sizes; Roofing sealants — related products for roof and gutter work.

How do I define the joint before choosing a sealant?

Identify every surface in contact with the sealant, including coatings, primers, backing materials and adjacent stone or metal. Record the joint width and depth, expected movement, indoor or outdoor exposure, water exposure, temperature and required appearance. These facts determine whether a general silicone, neutral-cure product, specialist glazing sealant, wet-area product or another system is appropriate.

How should I plan removal, preparation and cure?

Remove old sealant and loose material without damaging the adjoining surfaces; Clean and dry the joint using only compatible preparation products; Use backing material and joint dimensions where the product instructions require them; Mask, apply and tool within the stated working time; Protect the bead from water, movement and service until the relevant cure milestone.

How do I verify a specialist application?

Glazing, mirrors, natural stone, aquariums, drinking-water contact, structural joints and permanent immersion need explicit product coverage. Use the current Technical Data Sheet and Australian Safety Data Sheet for the supplied pack, and ask Selleys when the documentation does not establish compatibility.

What should I check for my job?

Selleys Storm is a premium waterproof sealant product designed to deliver immediate waterproof sealing on building materials in both wet and dry conditions, indoors or outdoors. It features Sil-X™ technology, a moisture-curing silyl-modified polymer (SMP) formulation that enables rapid waterproof sealing capability; Selleys Storm forms a waterproof seal instantly, even in wet conditions, is weather resistant and highly flexible (elongation at break exceeding 250%), is highly versatile for multiple materials, suitable for indoor and outdoor use, paintable with water-based exterior paints (two coats recommended), UV resistant, low odour, stops and prevents leaks, and has a non-slumping formula; Selleys Storm uses Sil-X™ technology, a moisture-curing silyl-modified polymer (SMP) formulation.

How do I compare the options?

Use this category to create a shortlist, then compare the exact candidates in a simple job table. Record the materials, location, exposure, movement or load, required finish, working time, support or protection period, full cure and major exclusions. A shared category or brand name does not make the products interchangeable.