Other Sealants

Why removal comes first

Resealing a joint is not a job you start with a new cartridge. Fresh sealant does not bond reliably to a cured bead, so applying over the old one produces a joint that looks finished and lifts at the interface later. On a wet area joint that has been in service, the old bead is also carrying whatever has grown or collected in it, and burying that under new sealant traps it against a food source rather than removing it.

The practical sequence is therefore: strip the old bead out, get the surface clean and ready, then apply the new sealant. Selleys Sealant Remover exists for the first of those steps — its description is specifically about leaving surfaces smooth and ready for a fresh start, which is the condition a new bead needs to bond to.

Where the sealant to reapply lives

Once the joint is stripped, choose the replacement by location rather than by what was there before — the original bead may not have been the right product in the first place:

The product in this category

What is in the Selleys "other sealants" category, and what is it for?

This category holds one product, and it is the one you need before you use anything else in the sealant range: Selleys Sealant Remover. It is described as making it easy to remove unwanted sealant, suiting clean-ups and renovations, and leaving surfaces smooth and ready for a fresh start.

This category contains one product. Use the information below to check whether it suits your job.

Define the joint before choosing the sealant

Identify every surface in contact with the sealant, including coatings, primers, backing materials and adjacent stone or metal. Record the joint width and depth, expected movement, indoor or outdoor exposure, water exposure, temperature and required appearance. These facts determine whether a general silicone, neutral-cure product, specialist glazing sealant, wet-area product or another system is appropriate.

Check cure type, adhesion requirements, tooling time, movement capability, paintability and excluded substrates on the exact product page. Do not treat elongation at break as a rated joint-movement figure. Water resistance, mould resistance and weather resistance also answer different questions and do not establish suitability for permanent immersion.

Plan removal, preparation and cure

  1. Remove old sealant and loose material without damaging the adjoining surfaces.
  2. Clean and dry the joint using only compatible preparation products.
  3. Use backing material and joint dimensions where the product instructions require them.
  4. Mask, apply and tool within the stated working time.
  5. Protect the bead from water, movement and service until the relevant cure milestone.

Verify specialist applications

Glazing, mirrors, natural stone, aquariums, drinking-water contact, structural joints and permanent immersion need explicit product coverage. Use the current Technical Data Sheet and Australian Safety Data Sheet for the supplied pack, and ask Selleys when the documentation does not establish compatibility.

What to check for your job

Compare the options: Other Sealants

Use this category to create a shortlist, then compare the exact candidates in a simple job table. Record the materials, location, exposure, movement or load, required finish, working time, support or protection period, full cure and major exclusions. A shared category or brand name does not make the products interchangeable.

  1. Suitability: both substrates, coatings and service conditions.
  2. Application: preparation, tools, dimensions, coverage and working time.
  3. Waiting: support removal, water exposure, sanding, painting and full cure.
  4. Finish: colour, visibility, flexibility, paintability and clean-up.
  5. Evidence: the current pack, Technical Data Sheet and Australian Safety Data Sheet.

Open the individual page for every shortlisted product. Where this category contains a retained discontinued page, use it to identify older stock or work and confirm current availability or a replacement directly with us.

Complete joint-planning checklist for Other Sealants

Record every adjoining material, coating and primer; the joint width and depth; expected movement; water, weather and temperature exposure; and the required colour, finish and paintability. Cure chemistry, substrate compatibility and joint geometry matter as much as the range name.

  1. Remove failed sealant and contamination without damaging the surrounding surface.
  2. Confirm whether primer, backing rod or a particular joint ratio is required.
  3. Plan masking, application and tooling within the published working time.
  4. Protect the bead from water, movement, dust and service during cure.
  5. Use the exact product documents for paint, immersion and maintenance limits.

Do not treat elongation at break as rated joint movement, or mould resistance as a promise of a maintenance-free joint. Aquariums, drinking water, natural stone, structural glazing and permanent immersion need explicit approval.

Details to check before you choose

More help for your project

Use these pages to compare the exact product, method or application that follows from Other Sealants. A related page is a route into more specific information, not evidence that every product is interchangeable.

Do I need sealant remover for every new sealing job?

No. It is an option for suitable jobs involving old sealant. Follow the chosen sealant’s preparation instructions.

Can Sealant Remover be used on polycarbonate or rubber?

No. Its directions exclude polycarbonate, rubber and EPDM. Test other surfaces and observe contact-time restrictions.

Why removal comes first?

Resealing a joint is not a job you start with a new cartridge. Fresh sealant does not bond reliably to a cured bead, so applying over the old one produces a joint that looks finished and lifts at the interface later. On a wet area joint that has been in service, the old bead is also carrying whatever has grown or collected in it, and burying that under new sealant traps it against a food source rather than removing it.

Where the sealant to reapply lives?

Once the joint is stripped, choose the replacement by location rather than by what was there before — the original bead may not have been the right product in the first place: Wet area silicone — showers, bathrooms, kitchens and laundries; Roofing silicone — roof and gutter joints and leak repair; Glass — glazing and window frames; Construction silicone — brick, concrete and structural joints; Multi-purpose — general sealing, adhesive sealants, clear and paintable options; Fire rated sealants — perimeter and penetration seals in fire-rated construction.

What is in the Selleys "other sealants" category, and what is it for?

This category holds one product, and it is the one you need before you use anything else in the sealant range: Selleys Sealant Remover . It is described as making it easy to remove unwanted sealant, suiting clean-ups and renovations, and leaving surfaces smooth and ready for a fresh start.

How do I define the joint before choosing a sealant?

Identify every surface in contact with the sealant, including coatings, primers, backing materials and adjacent stone or metal. Record the joint width and depth, expected movement, indoor or outdoor exposure, water exposure, temperature and required appearance. These facts determine whether a general silicone, neutral-cure product, specialist glazing sealant, wet-area product or another system is appropriate.

How should I plan removal, preparation and cure?

Remove old sealant and loose material without damaging the adjoining surfaces; Clean and dry the joint using only compatible preparation products; Use backing material and joint dimensions where the product instructions require them; Mask, apply and tool within the stated working time; Protect the bead from water, movement and service until the relevant cure milestone.

How do I verify a specialist application?

Glazing, mirrors, natural stone, aquariums, drinking-water contact, structural joints and permanent immersion need explicit product coverage. Use the current Technical Data Sheet and Australian Safety Data Sheet for the supplied pack, and ask Selleys when the documentation does not establish compatibility.

What should I check for my job?

The page highlights Selleys Silicone Remover, a product designed to remove old sealant quickly and easily. Selleys Sealant Remover exists for the first of those steps — its description is specifically about leaving surfaces smooth and ready for a fresh start, which is the condition a new bead needs to bond to.

How do I compare the options?

Use this category to create a shortlist, then compare the exact candidates in a simple job table. Record the materials, location, exposure, movement or load, required finish, working time, support or protection period, full cure and major exclusions. A shared category or brand name does not make the products interchangeable.

What should I know about complete joint-planning checklist for Other Sealants?

Record every adjoining material, coating and primer; the joint width and depth; expected movement; water, weather and temperature exposure; and the required colour, finish and paintability. Cure chemistry, substrate compatibility and joint geometry matter as much as the range name. Do not treat elongation at break as rated joint movement, or mould resistance as a promise of a maintenance-free joint.

What is the main product highlighted on the Selleys 'Other Sealants' page?

The page highlights Selleys Silicone Remover, a product designed to remove old sealant quickly and easily. Selleys Sealant Remover exists for the first of those steps — its description is specifically about leaving surfaces smooth and ready for a fresh start, which is the condition a new bead needs to bond to.