Removable Hooks & Glue | Damage-Free Hanging Solutions

Compare the products below with your materials, conditions and the finish you need.

Choose a product

Prepare, attach and remove

  1. Use a clean, structurally sound surface. Follow the retail hook instructions to clean and dry it; the TDS also mentions damp-surface adhesion, which should not override the preparation instructions for your installation.
  2. Apply the glue as directed on the pack and press the hook firmly for 30 seconds.
  3. Wait at least 24 hours and allow full cure before loading. Cold conditions can require longer.
  4. To remove, twist anticlockwise without pulling, then peel away residue. Check a small area first.

Removable Hooks & Glue

Selleys Undo combines removable glue gel with reusable hooks for hanging and decorating. Choose the correct hook size for the load and check that the surface is suitable before installation.

Hook loads after 24 hours

HookListed loadListed kit sizes
Small2 kg3, 4 or 10 hooks
Medium3 kg3, 4 or 10 hooks
Large5 kg2 hooks

These are the manufacturer’s specified hook loads, subject to the surface and installation instructions. They do not establish a general load rating for other objects bonded with the gel.

Define the bond before choosing the adhesive

Name both materials and any paint, coating, laminate or backing film. Decide whether each surface is porous, whether the joint has gaps, and whether it will face load, vibration, movement, weather, water or heat. A product that works on one timber-to-masonry joint may not be suitable for a mirror, flexible plastic, coated metal or continuously wet application.

Compare working time, repositioning time, initial grab, required bead pattern, temporary support and full cure. A fast-grab or rapid-setting statement does not mean immediate full strength. Heavy, stressed and overhead work may require support or mechanical fixing even when the adhesive has a high initial grab.

Prepare and assemble the joint

  1. Confirm the product covers both substrates and the service conditions.
  2. Remove dust, grease, moisture, loose coatings and release contamination as directed.
  3. Dry-fit the parts and plan supports before applying adhesive.
  4. Apply the stated bead, spread or contact method and assemble within the working time.
  5. Maintain support and avoid loading until the relevant cure instruction is satisfied.

Read limitations before application

Check excluded plastics, mirrors, polystyrene, permanent immersion, structural use and temperature limits on the exact product. Use the current pack label, Technical Data Sheet and Australian Safety Data Sheet. Where two manufacturer sources disagree, keep both values visible and ask which applies to the supplied formulation.

What to check for your job

Compare the options: Removable Hooks & Glue | Damage-Free Hanging Solutions

Use this category to create a shortlist, then compare the exact candidates in a simple job table. Record the materials, location, exposure, movement or load, required finish, working time, support or protection period, full cure and major exclusions. A shared category or brand name does not make the products interchangeable.

  1. Suitability: both substrates, coatings and service conditions.
  2. Application: preparation, tools, dimensions, coverage and working time.
  3. Waiting: support removal, water exposure, sanding, painting and full cure.
  4. Finish: colour, visibility, flexibility, paintability and clean-up.
  5. Evidence: the current pack, Technical Data Sheet and Australian Safety Data Sheet.

Open the individual page for every shortlisted product. Where this category contains a retained discontinued page, use it to identify older stock or work and confirm current availability or a replacement directly with us.

Complete bond-planning checklist for Removable Hooks & Glue | Damage-Free Hanging Solutions

Write down both substrates, including paint, coatings, laminates, backing films and whether each surface is porous. Define the joint gap, load direction, vibration, movement, water, weather, heat and required finish. These details decide whether the named product is suitable and whether temporary support or permanent mechanical fixing is required.

  1. Confirm both materials and every surface treatment are listed or otherwise covered by the current instructions.
  2. Separate working time, repositioning time, initial grab, support-removal time and full cure.
  3. Dry-fit the parts and prepare clamps, braces or fixings before opening the product.
  4. Follow the stated bead, spread, contact or assembly method.
  5. Keep the joint unloaded and within the specified conditions until the relevant cure milestone.

Do not transfer a strength, grab or cure claim from another formulation in the same range. Mirrors, flexible plastics, polystyrene, continuously wet areas, overhead work and structural loads require explicit product coverage.

More help for your project

Use these pages to compare the exact product, method or application that follows from Removable Hooks & Glue | Damage-Free Hanging Solutions. A related page is a route into more specific information, not evidence that every product is interchangeable.

Will Undo Glue always remove without marking a wall?

No. Use a suitable sound surface, test first and follow removal directions. Porous surfaces may stain, and extremely aged or compromised walls are excluded.

How long do I wait before loading a hook?

Allow at least 24 hours and full cure before loading. Cold conditions can require longer. Use the load rating for the exact hook size.

Can the adhesive be reused?

No. Reuse the hook with fresh Undo Glue; the adhesive is single use.

How long can I leave Undo Glue in place?

Contact our team to confirm for your item and surface. The technical sheet includes removal guidance of up to three days on porous surfaces and five days on non-porous surfaces, alongside a two-year renewal interval. Do not assume an unrestricted two-year installation.

How do I choose a product?

Undo Glue Gel — replacement glue in 5 g and 10 g tubes; Undo Hook & Glue kits — small, medium and large hooks with glue.

How do I prepare, attach and remove?

Use a clean, structurally sound surface. Follow the retail hook instructions to clean and dry it; the TDS also mentions damp-surface adhesion, which should not override the preparation instructions for your installation; Apply the glue as directed on the pack and press the hook firmly for 30 seconds; Wait at least 24 hours and allow full cure before loading. Cold conditions can require longer; To remove, twist anticlockwise without pulling, then peel away residue. Check a small area first.

What should I know about removable Hooks & Glue?

Selleys Undo combines removable glue gel with reusable hooks for hanging and decorating. Choose the correct hook size for the load and check that the surface is suitable before installation.

What should I know about hook loads after 24 hours?

These are the manufacturer’s specified hook loads, subject to the surface and installation instructions. They do not establish a general load rating for other objects bonded with the gel.

How do I define the bond before choosing the adhesive?

Name both materials and any paint, coating, laminate or backing film. Decide whether each surface is porous, whether the joint has gaps, and whether it will face load, vibration, movement, weather, water or heat. A product that works on one timber-to-masonry joint may not be suitable for a mirror, flexible plastic, coated metal or continuously wet application.

How do I prepare and assemble the joint?

Confirm the product covers both substrates and the service conditions; Remove dust, grease, moisture, loose coatings and release contamination as directed; Dry-fit the parts and plan supports before applying adhesive; Apply the stated bead, spread or contact method and assemble within the working time; Maintain support and avoid loading until the relevant cure instruction is satisfied.

How do I read limitations before application?

Check excluded plastics, mirrors, polystyrene, permanent immersion, structural use and temperature limits on the exact product. Use the current pack label, Technical Data Sheet and Australian Safety Data Sheet. Where two manufacturer sources disagree, keep both values visible and ask which applies to the supplied formulation.

What should I check for my job?

After 24 hours, the TDS lists 2 kg for small hooks, 3 kg for medium hooks and 5 kg for large hooks. Allow full cure before loading; cold conditions may extend the wait. These ratings depend on correct preparation and installation. Wait at least 24 hours and allow full cure before loading. the TDS also mentions damp-surface adhesion, which should not override the preparation instructions for your installation.