Selleys Undo Hooks & Glue
Compare the products below with your materials, conditions and the finish you need.
Choose a product
- Undo Glue Gel — replacement glue in 5 g and 10 g tubes.
- Undo Hook & Glue kits — small, medium and large hooks with glue.
Prepare, attach and remove
- Use a clean, structurally sound surface. Follow the retail hook instructions to clean and dry it; the TDS also mentions damp-surface adhesion, which should not override the preparation instructions for your installation.
- Apply the glue as directed on the pack and press the hook firmly for 30 seconds.
- Wait at least 24 hours and allow full cure before loading. Cold conditions can require longer.
- To remove, twist anticlockwise without pulling, then peel away residue. Check a small area first.
Selleys Undo Hooks & Glue
Selleys Undo combines removable glue gel with reusable hooks for hanging and decorating. Choose the correct hook size for the load and check that the surface is suitable before installation.
Hook loads after 24 hours
| Hook | Listed load | Listed kit sizes |
|---|---|---|
| Small | 2 kg | 3, 4 or 10 hooks |
| Medium | 3 kg | 3, 4 or 10 hooks |
| Large | 5 kg | 2 hooks |
These are the manufacturer’s specified hook loads, subject to the surface and installation instructions. They do not establish a general load rating for other objects bonded with the gel.
Use this category to build a shortlist
Start with the exact job, materials and conditions. Record the substrate and any coating, whether the surface is porous, the size of the repair or joint, indoor or outdoor exposure, water, heat, movement, load and the finish required. Products grouped on one category page can still differ in chemistry, working time, cure, limitations and safety.
Open each candidate product and compare the current instructions. Separate working time, support or protection time, paint or sanding readiness and full cure. Check whether the finished work must remain flexible, accept paint, tolerate weather or water, or carry load.
Prepare the work before opening the pack
- Read the full method and limitations for the exact product.
- Clean, dry and prepare the surface using compatible materials.
- Gather tools, masking, supports and personal protective equipment.
- Confirm temperature, weather and ventilation for application and cure.
- Follow the stated dimensions, coverage and waiting times.
Confirm documents and availability
Use the current pack label, Technical Data Sheet and Australian Safety Data Sheet. Category pages and retained discontinued-product pages help with comparison but do not establish current stock or a replacement product. Ask Selleys when a required material, exposure or use is not expressly covered.
What to check for your job
- After 24 hours, the TDS lists 2 kg for small hooks, 3 kg for medium hooks and 5 kg for large hooks. Allow full cure before loading; cold conditions may extend the wait. These ratings depend on correct preparation and installation. Wait at least 24 hours and allow full cure before loading. the TDS also mentions damp-surface adhesion, which should not override the preparation instructions for your installation.
- Twist the hook anticlockwise, then peel away the glue residue. Never pull the hook straight off. Test the surface first; removal can damage weak paint or compromised surfaces. To remove, twist anticlockwise without pulling, then peel away residue. Follow the retail hook instructions to clean and dry it
- The hooks are reusable with fresh glue. The glue itself is single use. The manufacturer recommends renewing the glue every two years.
- Wait at least 28 days after painting. Use structurally sound surfaces, test first, and avoid surfaces vulnerable to damage or staining. The TDS excludes polyethylene, polypropylene and PTFE. Use mechanical fasteners for valuable items. Wait at least 24 hours and allow full cure before loading.
- The published directions contain ambiguous wording about three days on porous surfaces and five days on non-porous surfaces, alongside advice to renew glue every two years. Do not treat those statements as a guaranteed removal window or maximum installed life. Ask our team to clarify what applies to your surface.
- Yes. We publish an Australian Safety Data Sheet for Undo Glue. Read the current SDS and pack label for handling, protection, first aid and storage instructions.
Compare the options: Selleys Undo Hooks & Glue
Use this category to create a shortlist, then compare the exact candidates in a simple job table. Record the materials, location, exposure, movement or load, required finish, working time, support or protection period, full cure and major exclusions. A shared category or brand name does not make the products interchangeable.
- Suitability: both substrates, coatings and service conditions.
- Application: preparation, tools, dimensions, coverage and working time.
- Waiting: support removal, water exposure, sanding, painting and full cure.
- Finish: colour, visibility, flexibility, paintability and clean-up.
- Evidence: the current pack, Technical Data Sheet and Australian Safety Data Sheet.
Open the individual page for every shortlisted product. Where this category contains a retained discontinued page, use it to identify older stock or work and confirm current availability or a replacement directly with us.
Complete bond-planning checklist for Selleys Undo Hooks & Glue
Write down both substrates, including paint, coatings, laminates, backing films and whether each surface is porous. Define the joint gap, load direction, vibration, movement, water, weather, heat and required finish. These details decide whether the named product is suitable and whether temporary support or permanent mechanical fixing is required.
- Confirm both materials and every surface treatment are listed or otherwise covered by the current instructions.
- Separate working time, repositioning time, initial grab, support-removal time and full cure.
- Dry-fit the parts and prepare clamps, braces or fixings before opening the product.
- Follow the stated bead, spread, contact or assembly method.
- Keep the joint unloaded and within the specified conditions until the relevant cure milestone.
Do not transfer a strength, grab or cure claim from another formulation in the same range. Mirrors, flexible plastics, polystyrene, continuously wet areas, overhead work and structural loads require explicit product coverage.
More help for your project
Use these pages to compare the exact product, method or application that follows from Selleys Undo Hooks & Glue. A related page is a route into more specific information, not evidence that every product is interchangeable.
- Removable Hooks & Glue | Damage-Free Hanging Solutions — Selleys Undo combines removable glue gel with reusable hooks for hanging and decorating. Choose the correct hook size for the load and check that the surface is suitable before installation.
- Undo Glue Gel — Selleys Undo combines removable glue gel with reusable hooks for hanging and decorating. Choose the correct hook size for the load and check that the surface is suitable before installation.
- Undo Glue Hook & Gel — Selleys Undo combines removable glue gel with reusable hooks for hanging and decorating. Choose the correct hook size for the load and check that the surface is suitable before installation.
- Choosing an adhesive for Bakelite — First confirm that the material is Bakelite. Our expert advice recommends a two-part epoxy, but the working time depends on the exact product you have.
- Best Glue for Frameless Shower Screens — A silicone sealant will do this job — either a neutral cure or an acetic cure product is generally fine on a tiled floor.
- Best Glue for Australian Hardwood — For most hardwood joinery, Aquadhere Exterior Wood Glue is the right answer.
- How To Glue Glass Back Onto an Oven Door — The reason it suits the job is its temperature range.
- Gluing an acrylic bookend — For the described right-angle bookend made from two 3 mm acrylic pieces, our expert answer names Selleys Fix & Go Multi Grip. This is not a measured claim that it is the strongest adhesive for every acrylic joint.
Product instructions and safety sheets
Ready to choose a product? Use the links below for the products featured on this page. Check the exact product, pack and application before you start. Each product has its own directions and limitations.
- Undo Glue Gel — product details and pack options
- Undo Glue Hook & Gel — product details and pack options
Need help matching a document or checking your job? Contact our team. You can also find a store.
Will Undo Glue damage my wall?
Clean removal depends on a suitable surface and correct application and removal. Pre-test, wait at least 28 days after painting, avoid compromised walls and remember porous surfaces may stain. Never pull a hook towards you.
How long before I can hang something?
Allow full cure before loading. Our online directions say 24 hours; low temperatures slow cure. Use the capacity for the actual hook size.
Can I use it without a hook?
Yes, for suitable lightweight posters, prints, paper and decorations. Hook capacities do not apply to directly mounted items. Check the removal method for delicate paper with the pack or our team.
Can I reuse the glue?
No. Reuse the hook with fresh Undo Glue; the adhesive is single use.
Can I leave a hook up for two years and guarantee clean removal?
No unconditional guarantee follows from that recommendation. Ask our team about the technical sheet’s differing removal-duration notes for your surface and intended mounting period before applying.
How do I choose a product?
Undo Glue Gel — replacement glue in 5 g and 10 g tubes; Undo Hook & Glue kits — small, medium and large hooks with glue.
How do I prepare, attach and remove?
Use a clean, structurally sound surface. Follow the retail hook instructions to clean and dry it; the TDS also mentions damp-surface adhesion, which should not override the preparation instructions for your installation; Apply the glue as directed on the pack and press the hook firmly for 30 seconds; Wait at least 24 hours and allow full cure before loading. Cold conditions can require longer; To remove, twist anticlockwise without pulling, then peel away residue. Check a small area first.
What should I know about Selleys Undo Hooks & Glue?
Selleys Undo combines removable glue gel with reusable hooks for hanging and decorating. Choose the correct hook size for the load and check that the surface is suitable before installation.
What should I know about hook loads after 24 hours?
These are the manufacturer’s specified hook loads, subject to the surface and installation instructions. They do not establish a general load rating for other objects bonded with the gel.
What should I know about use this category to build a shortlist?
Start with the exact job, materials and conditions. Record the substrate and any coating, whether the surface is porous, the size of the repair or joint, indoor or outdoor exposure, water, heat, movement, load and the finish required. Products grouped on one category page can still differ in chemistry, working time, cure, limitations and safety.
How do I prepare the work before opening the pack?
Read the full method and limitations for the exact product; Clean, dry and prepare the surface using compatible materials; Gather tools, masking, supports and personal protective equipment; Confirm temperature, weather and ventilation for application and cure; Follow the stated dimensions, coverage and waiting times.
How do I confirm documents and availability?
Use the current pack label, Technical Data Sheet and Australian Safety Data Sheet. Category pages and retained discontinued-product pages help with comparison but do not establish current stock or a replacement product. Ask Selleys when a required material, exposure or use is not expressly covered.