Product

Product Facts

Product Name
Selleys Pro Trade Glass Silicone
Brand
Selleys
Category
Home & Garden > Sealants & Adhesives

Selleys Pro Trade Glass Silicone

Selleys Pro Trade Glass Silicone is an 100% neutral cure silicone with excellent weather and UV resistance and a matte finish.

Check the pack details below, then find a retailer near you. Range and availability vary by store.

Selleys Pro Trade Glass Silicone — product image

Product details

Pack, technology and materials
TechnologyNeutral cure silicone

Selleys Pro Trade Glass Silicone: technical details

Technical data · page 1
PropertyTypical Result
TechnologyNeutral (oxime) cure silicone
ColourClear, black
Density1.02 (clear)
1.33 (black)
Application
Temperature
Minimum 5°C
Skin Time
25°C / 50% RH
5 – 10 minutes
Cure Rate10mm in 5–7 days
SlumpNo Slump
Tensile
Strength
2.0 MPa (clear)
1.3 MPa (black)
Shore A28 (clear)
30 (black)
Hardness
Elongation at
Break
400% (clear)
>680% (black)
Movement+/- 25%
Capability
Service
Temperature
-60 – 180°C (clear)
-40 – 140°C (black)
VOC Content33 g/L (clear)
38 g/L (black)
SCAQMD Method
304-91
Indicative data only, not intended for preparation of specifications
Technical data · page 1
PackagingSizeColour
Cartridge300gClear
Cartridge400gBlack

What it does

  • Ideal for most common building and glazing substrates* including glass, aluminium, non-oily timber, concrete, masonry, most metals and powder coated surfaces
  • Weather & UV resistant
  • Strong adhesion to glass
  • Low slump
  • Matt finish
  • Will not corrode metals
  • Meets GBCA limits for VOC of max 50g/L *Pretest on substrates is recommended.

Tested performance and standards

BS 5889 approved (clear)

Conditions and compatibility

  • Not suitable for structural glazing
  • Not suitable for submerged joints where porous substrates permit water to the bind interface
  • Not suitable for aquarium construction
  • Should not be applied in contact with bituminous materials or some rubber products as these may contain components which can migrate into the sealant and result in staining or reduced performance.
  • Complete painting before applying sealant, as sealant cannot be successfully painted over.

Technical data sheet · 23/07/2020

Where to use it

Pro-Trade Glass Sealant is suitable for windows and glass, mirrors, splash backs, auto, RV, bus, boat, factory assembly, expansion joints, weather sealing, solar panels. Also suitable for industrial, potable water and automotive sealing applications. Can be used as an adhesive and sealant.

Source: Technical data sheet, page 1.

Prepare the surface

Surfaces must be clean, dry, and free of dirt, grease, oil or water. Metal and glass surfaces should be cleaned with general-purpose thinners or mineral turpentine and allowed to dry.

Source: Technical data sheet, page 1.

How to apply

Cut nozzle at 450 angle to desired bead width and apply to substrate using a sealant gun. Tooling time is 5-10 minutes. Tack free time is approx. 1 hour. Some surfaces may need a primer. If so, allow primer to dry before applying sealant. Use approved backing material for joints over 10mm deep.

Source: Technical data sheet, page 1.

Application tips

For a neat appearance use masking tape and remove before sealant has skinned over.

Source: Technical data sheet, page 1.

Clean up

Uncured sealant can be cleaned up with mineral turpentine.

Source: Technical data sheet, page 2.

Storage

12 months from date of manufacture if stored below 28°C

Source: Technical data sheet, page 2.

Where not to use it

  • Not suitable for structural glazing
  • Not suitable for submerged joints where porous substrates permit water to the bind interface
  • Not suitable for aquarium construction
  • Should not be applied in contact with bituminous materials or some rubber products as these may contain components which can migrate into the sealant and result in staining or reduced performance.
  • Complete painting before applying sealant, as sealant cannot be successfully painted over.

Source: Technical data sheet, page 2.

Safety before you start

Check the product name on your pack against the Australian SDS below before use.

SELLEYS PRO-TRADE GLASS SILICONE

SDS signal word: Warning.

Handling: Avoid eye contact and skin contact. Avoid inhalation of dust.

Protective equipment and ventilation

Wear safety shoes, overalls, gloves, safety glasses. Available information suggests that gloves made from nitrile rubber should be suitable for intermittent contact. However, due to variations in glove construction and local conditions, the user should make a final assessment. Always wash hands before smoking, eating, drinking or using the toilet. Wash contaminated clothing and other protective equipment before storing or re-using.

Ventilation: Natural ventilation should be adequate under normal use conditions.

Australian safety data sheet · issued 10 July 2025 · sections 2, 7 and 8. Read the full SDS for first aid, spill response, incompatibilities and disposal.

SELLEYS PRO-TRADE GLASS SILICONE: storage and product data

Match your pack
Pack named in this SDSProduct codeBarcode
PRO-TRADE Glass Silicone Clear 300g1021039300697129888
PRO-TRADE Glass Silicone Black 300g1021049300697129895

Store between jobs

Store in a cool, dry, well-ventilated place and out of direct sunlight. Store away from foodstuffs. Store away from incompatible materials described in Section 10. Store away from sources of heat and/or ignition. Take precautions against static electricity discharges. Keep container standing upright. Keep containers closed when not in use - check regularly for spills.

Classified as a C1 (COMBUSTIBLE LIQUID) for the purpose of storage and handling, in accordance with the requirements of AS 1940. Refer to State Regulations for storage and transport requirements.

Typical physical properties from this SDS
FormPaste
ColourColourless
OdourMild characteristic
SolubilityInsoluble in water
Specific Gravity1.04
Relative Vapour Density (air=1)>1
Vapour PressureN Av
Flash Point (°C)63.00
Explosion/Flammability LimitsN Av
Autoignition Temperature (°C)450
Melting Point/Range (°C)N Av
Boiling Point/Range (°C)N Av
pHN App
Viscosity>7 mm²/s @ 40 °C
Total VOC (g/Litre)N Av

Others in this range

Alongside this product:

Browse from here

Where this page sits:

Elsewhere in this category

Nearby products and groups:

Typical values describe the material in this safety data sheet. They are not application instructions or performance guarantees. N Av means not available; N App means not applicable.

Ingredients disclosed in the SDS
CHEMICAL ENTITY CAS NO PROPORTION
2-Butanone, O,O',O''-(methylsilylidyne)trioxime 22984-54-9 1 - 10 % (w/w)
2-Butanone, O,O',O''-(ethenylsilylidyne)trioxime 2224-33-1 <1 % (w/w)
Cyclotetrasiloxane, octamethyl- 556-67-2 <1 % (w/w)
N-[3-(Trimethoxysilyl)propyl]ethylenediamine 1760-24-3 <1 % (w/w)
Ingredients determined to be non-hazardous or below reporting limits Balance
____________
100%

These are the ingredients disclosed for hazard communication, not the complete formulation. Use the application instructions to decide suitability for your project.

First aid from the matching SDS

If poisoning occurs, contact a doctor or Poisons Information Centre (Phone Australia 131 126, New Zealand 0800 764 766).

Inhalation: Remove victim from exposure - avoid becoming a casualty. Remove contaminated clothing and loosen remaining clothing. Allow patient to assume most comfortable position and keep warm. Keep at rest until fully recovered. Seek medical advice if effects persist.

Skin Contact: Effects may be delayed. If skin or hair contact occurs, immediately remove contaminated clothing and flush skin and hair with running water. Continue flushing with water until advised to stop by the Poisons Information Centre or a Doctor; or for 15 minutes and transport to Doctor or Hospital. For gross contamination, immediately drench with water and remove clothing. Continue to flush skin and hair with plenty of water (and soap if material is insoluble). For skin burns, cover with a clean, dry dressing until medical help is available. If blistering occurs, do NOT break blisters. If swelling, redness, blistering, or irritation occurs seek medical assistance.

Eye contact: If in eyes wash out immediately with water. In all cases of eye contamination it is a sensible precaution to seek medical advice.

Ingestion: Rinse mouth with water. If swallowed, do NOT induce vomiting. Give a glass of water to drink. Never give anything by the mouth to an unconscious patient. If vomiting occurs give further water. Seek medical advice.

PPE for First Aiders: Wear safety shoes, overalls, gloves, safety glasses. Available information suggests that gloves made from nitrile rubber should be suitable for intermittent contact. However, due to variations in glove construction and local conditions, the user should make a final assessment. Always wash hands before smoking, eating, drinking or using the toilet. Wash contaminated clothing and other protective equipment before storing or re-using.

Notes to physician: Treat symptomatically. Effects may be delayed.

Disposal

Persons conducting disposal, recycling or reclamation activities should ensure that appropriate personal protection equipment is used, see "Section 8. Exposure Controls and Personal Protection" of this SDS. If possible material and its container should be recycled. If material or container cannot be recycled, dispose in accordance with local, regional, national and international Regulations.

Australian SDS · sections 1, 3, 4, 7, 9 and 13 · 10 July 2025

Technical and safety documents

The technical data sheet covers application and performance conditions. The safety data sheet covers hazards and safe handling. Use both alongside the pack instructions.

Need a hand choosing the right document or checking your application? Contact our team with the product name, pack code, surfaces and intended use.

Do clear and black share the same heat limits?

No. TDS service ranges are −60°C to 180°C for clear and −40°C to 140°C for black. Their other technical properties also differ.

Can it be used to build an aquarium or structurally glaze?

No. Both are excluded, as are submerged joints where porous substrates allow water to the bond interface.

What black pack should I match to the SDS?

The TDS lists black 400 g but the linked SDS lists black 300 g. Ask our team to confirm the correct documents for your exact pack.

How soon does a 10 mm depth cure?

The TDS states 10 mm in 5–7 days, with skinning 5–10 minutes and tack-free time about one hour. These are different stages.

What are the key product details?

Ideal for most common building and glazing substrates* including glass, aluminium, non-oily timber, concrete, masonry, most metals and powder coated surfaces; Weather & UV resistant; Strong adhesion to glass; Will not corrode metals; Meets GBCA limits for VOC of max 50g/L *Pretest on substrates is recommended; Not suitable for structural glazing; Not suitable for submerged joints where porous substrates permit water to the bind interface; Not suitable for aquarium construction; Should not be applied in contact with bituminous materials or some rubber products as these may contain components which can migrate into the sealant and result in staining or reduced performance.

Where can I use it?

Pro-Trade Glass Sealant is suitable for windows and glass, mirrors, splash backs, auto, RV, bus, boat, factory assembly, expansion joints, weather sealing, solar panels. Also suitable for industrial, potable water and automotive sealing applications. Can be used as an adhesive and sealant.

How do I prepare the surface?

Surfaces must be clean, dry, and free of dirt, grease, oil or water. Metal and glass surfaces should be cleaned with general-purpose thinners or mineral turpentine and allowed to dry.

How do I apply it?

Cut nozzle at 450 angle to desired bead width and apply to substrate using a sealant gun. Tooling time is 5-10 minutes. Tack free time is approx. 1 hour. Some surfaces may need a primer. If so, allow primer to dry before applying sealant. Use approved backing material for joints over 10mm deep.

What should I know about safety before I start?

Check the product name on your pack against the Australian SDS below before use. Handling: Avoid eye contact and skin contact. Avoid inhalation of dust. Wear safety shoes, overalls, gloves, safety glasses. Available information suggests that gloves made from nitrile rubber should be suitable for intermittent contact.

Which technical and safety documents are available?

The technical data sheet covers application and performance conditions. The safety data sheet covers hazards and safe handling. Use both alongside the pack instructions. Need a hand choosing the right document or checking your application? Contact our team with the product name, pack code, surfaces and intended use.

What should I know about SELLEYS PRO-TRADE GLASS SILICONE?

Store in a cool, dry, well-ventilated place and out of direct sunlight. Store away from foodstuffs. Store away from incompatible materials described in Section 10. Store away from sources of heat and/or ignition. Take precautions against static electricity discharges. Keep container standing upright. Keep containers closed when not in use - check regularly for spills.

What are its physical and chemical properties?

Form: Paste; Colour: Clear, black; Odour: Mild characteristic; pH: N App; Viscosity: 7 mm²/s @ 40 °C; Specific Gravity: 1.04; Solubility: Insoluble in water; Boiling Point/Range (°C): N Av; Melting Point/Range (°C): N Av; Vapour Pressure: N Av; Relative Vapour Density (air=1): 1.