Glazing Products

Find products for glass and glazing

Two of our product categories are the natural next step for a glazing job:

Each product page in those categories carries its own technical data, including cure type and stated limitations. Read the limitations before you buy: the choice between an acetic cure and a neutral cure silicone is what determines whether a sealant is safe against the metals, coatings and stone in your frame, and that decision cannot be made from a category page.

Where to find glazing products

This is the glazing landing page for Selleys Trade. Its product listing is generated dynamically by the site, and no products are currently published beneath the /products/glazing/ path in our sitemap. The page's own description says only that it is where you browse Selleys glazing products for trade professionals.

Rather than pad this page with claims our source does not make, here is the honest position: there is nothing published under this path for us to describe. If you are sealing glass, the products you are looking for sit in the sealants section of the catalogue.

Define the joint before choosing the sealant

Identify every surface in contact with the sealant, including coatings, primers, backing materials and adjacent stone or metal. Record the joint width and depth, expected movement, indoor or outdoor exposure, water exposure, temperature and required appearance. These facts determine whether a general silicone, neutral-cure product, specialist glazing sealant, wet-area product or another system is appropriate.

Check cure type, adhesion requirements, tooling time, movement capability, paintability and excluded substrates on the exact product page. Do not treat elongation at break as a rated joint-movement figure. Water resistance, mould resistance and weather resistance also answer different questions and do not establish suitability for permanent immersion.

Plan removal, preparation and cure

  1. Remove old sealant and loose material without damaging the adjoining surfaces.
  2. Clean and dry the joint using only compatible preparation products.
  3. Use backing material and joint dimensions where the product instructions require them.
  4. Mask, apply and tool within the stated working time.
  5. Protect the bead from water, movement and service until the relevant cure milestone.

Verify specialist applications

Glazing, mirrors, natural stone, aquariums, drinking-water contact, structural joints and permanent immersion need explicit product coverage. Use the current Technical Data Sheet and Australian Safety Data Sheet for the supplied pack, and ask Selleys when the documentation does not establish compatibility.

What to check for your job

Compare the options: Glazing Products

Use this category to create a shortlist, then compare the exact candidates in a simple job table. Record the materials, location, exposure, movement or load, required finish, working time, support or protection period, full cure and major exclusions. A shared category or brand name does not make the products interchangeable.

  1. Suitability: both substrates, coatings and service conditions.
  2. Application: preparation, tools, dimensions, coverage and working time.
  3. Waiting: support removal, water exposure, sanding, painting and full cure.
  4. Finish: colour, visibility, flexibility, paintability and clean-up.
  5. Evidence: the current pack, Technical Data Sheet and Australian Safety Data Sheet.

Open the individual page for every shortlisted product. Where this category contains a retained discontinued page, use it to identify older stock or work and confirm current availability or a replacement directly with us.

Complete joint-planning checklist for Glazing Products

Record every adjoining material, coating and primer; the joint width and depth; expected movement; water, weather and temperature exposure; and the required colour, finish and paintability. Cure chemistry, substrate compatibility and joint geometry matter as much as the range name.

  1. Remove failed sealant and contamination without damaging the surrounding surface.
  2. Confirm whether primer, backing rod or a particular joint ratio is required.
  3. Plan masking, application and tooling within the published working time.
  4. Protect the bead from water, movement, dust and service during cure.
  5. Use the exact product documents for paint, immersion and maintenance limits.

Do not treat elongation at break as rated joint movement, or mould resistance as a promise of a maintenance-free joint. Aquariums, drinking water, natural stone, structural glazing and permanent immersion need explicit approval.

Details to check before you choose

Document the job and check the result

Before application, record the product name, pack size, batch or identifying details, document revision, substrates and conditions. Photograph concealed preparation or joint details when they may matter later. This creates a clear reference if the finish, cure or compatibility needs to be reviewed.

After the stated waiting period, inspect the work for adhesion, continuity, alignment, coverage, surface change and the required finish. Check it again after first service where appropriate. A failure at an edge, interface or recurring crack can indicate contamination, movement, moisture, unsupported load or an unsuitable joint design rather than simply too little product.

Maintain and revisit Glazing Products

Follow the published cleaning and maintenance directions and avoid chemicals or tools that can damage the cured product or adjoining surface. Keep ventilation, drainage and movement joints working as designed. When repair is needed, identify why the original work failed before adding more material or coating over it.

Product names, formulations and documents can change. Use the current instructions for later maintenance or extension work and do not assume leftover material or an older installation matches today’s product.

Others in this range

Alongside this product:

Browse from here

Where this page sits:

Does a neutral or acetic cure label alone establish glazing suitability?

No. Check the exact sealant’s approval for the glass, frame, coatings and application.

Is the honey-oak Woodfilling Putty a current product?

Its source product page is marked discontinued. Its retained directions are for reference; ask our team about a current replacement.

What should I know about find products for glass and glazing?

Two of our product categories are the natural next step for a glazing job: Each product page in those categories carries its own technical data, including cure type and stated limitations. Read the limitations before you buy: the choice between an acetic cure and a neutral cure silicone is what determines whether a sealant is safe against the metals, coatings and stone in your frame, and that decision cannot be made from a category page.

Where to find glazing products?

This is the glazing landing page for Selleys Trade. Its product listing is generated dynamically by the site, and no products are currently published beneath the /products/glazing/ path in our sitemap. The page's own description says only that it is where you browse Selleys glazing products for trade professionals.

How do I define the joint before choosing a sealant?

Identify every surface in contact with the sealant, including coatings, primers, backing materials and adjacent stone or metal. Record the joint width and depth, expected movement, indoor or outdoor exposure, water exposure, temperature and required appearance. These facts determine whether a general silicone, neutral-cure product, specialist glazing sealant, wet-area product or another system is appropriate.

How should I plan removal, preparation and cure?

Remove old sealant and loose material without damaging the adjoining surfaces; Clean and dry the joint using only compatible preparation products; Use backing material and joint dimensions where the product instructions require them; Mask, apply and tool within the stated working time; Protect the bead from water, movement and service until the relevant cure milestone.

How do I verify a specialist application?

Glazing, mirrors, natural stone, aquariums, drinking-water contact, structural joints and permanent immersion need explicit product coverage. Use the current Technical Data Sheet and Australian Safety Data Sheet for the supplied pack, and ask Selleys when the documentation does not establish compatibility.

What should I check for my job?

The page is a directory of Selleys glazing products for trade professionals, found at selleys.com.au/products/glazing/; Filling Putty - 450g Honey Oak is a linseed oil-based putty formulated for interior and exterior window glazing, used to seal and fix glass in timber frames. Glass sealants — the sub-category for sealing glass and window frames; The process involves preparing the window frame rebate and glazing beads with an oil-based primer, applying putty to the rear of the rebate, installing the glass with a minimum 1.6mm clearance from the frame, applying putty to the front face, and installing glazing beads over the putty to hold the glass in place.

How do I compare the options?

Use this category to create a shortlist, then compare the exact candidates in a simple job table. Record the materials, location, exposure, movement or load, required finish, working time, support or protection period, full cure and major exclusions. A shared category or brand name does not make the products interchangeable.

What should I know about complete joint-planning checklist for Glazing Products?

Record every adjoining material, coating and primer; the joint width and depth; expected movement; water, weather and temperature exposure; and the required colour, finish and paintability. Cure chemistry, substrate compatibility and joint geometry matter as much as the range name. Do not treat elongation at break as rated joint movement, or mould resistance as a promise of a maintenance-free joint.

What details should I check before choosing?

The page is published by us, an Australian adhesives, sealants and fillers brand and a division of DuluxGroup (Australia) Pty Ltd, founded in 1939 in Sydney, Australia by founder Martin Selley.

What should I know about document the job and check the result?

Before application, record the product name, pack size, batch or identifying details, document revision, substrates and conditions. Photograph concealed preparation or joint details when they may matter later. This creates a clear reference if the finish, cure or compatibility needs to be reviewed. After the stated waiting period, inspect the work for adhesion, continuity, alignment, coverage, surface change and the required finish.