Product

Product Facts

Product Name
Selleys No More Gaps Interior Multipurpose
Brand
Selleys
Category
Home & Garden > Building & Hardware Supplies

No More Gaps Interior Multipurpose

Trust Selleys for all your interior gap filling needs. Our No More Gaps Interior Multipurpose gap filler delivers a smooth finish with superior flexibility and low shrinkage.

Check the pack details below, then find a retailer near you. Range and availability vary by store.

No More Gaps Interior Multipurpose — product image

Product details

Pack, technology and materials
ColourWhite
TechnologyAcrylic-based

No More Gaps Interior Multipurpose: technical details

Suitable interior gaps

Use for gaps and cracks around skirting boards, cornices, and the inside of window and door frames. The TDS lists plasterboard, wood, particleboard, cement sheeting, aluminium and glass.

Source: Technical data sheet, page 1.

Prepare, fill and finish

  1. Clean and dry the surfaces; remove dust and grease.
  2. Cut the nozzle at 45°, cut the cartridge tip, fit the nozzle and load the gun.
  3. Push the filler into the gap or joint with the caulking gun.
  4. Smooth with a wet, gloved finger or spatula.
  5. Remove wet excess with a damp cloth. Use a scraper for dry excess.

Source: Technical data sheet, page 1.

When to paint

The application instructions give approximately 30 minutes for a skin to form before painting. This guidance is qualified for gaps no larger than 5 mm deep and 10 mm wide, at temperatures above 10°C.

Let the filler dry before painting and avoid a thick paint coat. Allow 24–48 hours before oil-based paint; flat and ceiling paints require longer drying because they flex less as the filler dries.

Source: Technical data sheet, page 1.

Limits and storage

  • Do not apply or store below 5°C.
  • Do not use for permanent water immersion or constantly damp areas.
  • Do not use between tongue-and-groove boards or weatherboards; the TDS directs those applications to No More Gaps Exterior.

Keep the container sealed in a cool place away from direct sunlight, above 5°C. The TDS gives an unopened-cartridge shelf life of 24 months.

Source: Technical data sheet, page 2.

Safety before you start

Check the product name on your pack against the Australian SDS below before use.

SELLEYS NO MORE GAPS INTERIOR MULTIPURPOSE

The Australian SDS does not classify this material as hazardous under its stated classification criteria. Follow the handling and protective measures in the SDS.

CONTAINS ISOTHIAZOLINONES. Repeated contact may cause sensitization.

Handling: Avoid eye contact and repeated or prolonged skin contact. Avoid inhalation of dust.

Protective equipment and ventilation

Wear safety shoes, overalls, gloves, safety glasses. Available information suggests that gloves made from nitrile rubber should be suitable for intermittent contact. However, due to variations in glove construction and local conditions, the user should make a final assessment. Always wash hands before smoking, eating, drinking or using the toilet. Wash contaminated clothing and other protective equipment before storing or re-using.

Ventilation: Natural ventilation should be adequate under normal use conditions.

Australian safety data sheet · issued 29 April 2024 · sections 2, 7 and 8. Read the full SDS for first aid, spill response, incompatibilities and disposal.

SELLEYS NO MORE GAPS INTERIOR: storage and product data

Match your pack
Pack named in this SDSProduct codeBarcode
No More Gaps Int MultipurposeTube 1501020949300697128966
No More Gaps Int Multipurpose White 475g NZ1019019300697115263
No More Gaps Int Multipurpose White 475g SRP1018999300697115263

Store between jobs

Store in a cool, dry, well-ventilated place and out of direct sunlight. Store away from foodstuffs. Store away from incompatible materials described in Section 10. Store away from sources of heat and/or ignition. Keep container standing upright. Keep containers closed when not in use - check regularly for spills.

Typical physical properties from this SDS
FormPaste
ColourWhite
OdourCharacteristic
SolubilityDispersible in water
Specific Gravity1.60 - 1.65
Relative Vapour Density (air=1)>1
Vapour PressureN Av
Flash Point (°C)N App
Explosion/Flammability LimitsN App
Autoignition Temperature (°C)N Av
Melting Point/Range (°C)N Av
Boiling Point/Range (°C)N Av
pHN Av
Viscosity>20.5 mm²/s @ 40 °C
Total VOC (g/Litre)N Av

Others in this range

Alongside this product:

Browse from here

Where this page sits:

Typical values describe the material in this safety data sheet. They are not application instructions or performance guarantees. N Av means not available; N App means not applicable.

Ingredients disclosed in the SDS
CHEMICAL ENTITY CAS NO PROPORTION
Ingredients determined to be non-hazardous or below reporting limits 100 % (w/w)
____________
100%

These are the ingredients disclosed for hazard communication, not the complete formulation. Use the application instructions to decide suitability for your project.

First aid from the matching SDS

If poisoning occurs, contact a doctor or Poisons Information Centre (Phone Australia 131 126, New Zealand 0800 764 766).

Inhalation: Remove victim from exposure - avoid becoming a casualty. Remove contaminated clothing and loosen remaining clothing. Allow patient to assume most comfortable position and keep warm. Keep at rest until fully recovered. Seek medical advice if effects persist.

Skin Contact: If skin or hair contact occurs, remove contaminated clothing and flush skin and hair with running water. If swelling, redness, blistering or irritation occurs seek medical assistance.

Eye contact: If in eyes wash out immediately with water. In all cases of eye contamination it is a sensible precaution to seek medical advice.

Ingestion: Rinse mouth with water. If swallowed, do NOT induce vomiting. Give a glass of water to drink. Never give anything by the mouth to an unconscious patient. If vomiting occurs give further water. Seek medical advice.

PPE for First Aiders: Wear safety shoes, overalls, gloves, safety glasses. Available information suggests that gloves made from nitrile rubber should be suitable for intermittent contact. However, due to variations in glove construction and local conditions, the user should make a final assessment. Always wash hands before smoking, eating, drinking or using the toilet. Wash contaminated clothing and other protective equipment before storing or re-using.

Notes to physician: Treat symptomatically.

Disposal

Persons conducting disposal, recycling or reclamation activities should ensure that appropriate personal protection equipment is used, see "Section 8. Exposure Controls and Personal Protection" of this SDS. If possible material and its container should be recycled. If material or container cannot be recycled, dispose in accordance with local, regional, national and international Regulations.

Australian SDS · sections 1, 3, 4, 7, 9 and 13 · 29 April 2024

Technical and safety documents

The technical data sheet covers application and performance conditions. The safety data sheet covers hazards and safe handling. Use both alongside the pack instructions.

Need a hand choosing the right document or checking your application? Contact our team with the product name, pack code, surfaces and intended use.

Is 30 minutes the full-cure time?

No. The technical sheet distinguishes skinning and qualified painting guidance. Its table gives 20 minutes at 23°C/50% humidity; its method says about 30 minutes before painting with conditions.

Can I paint with oil-based paint straight away?

No. Allow 24–48 hours and longer where needed. Use gaps no larger than 10mm wide and 5mm deep and apply above 10°C for that painting guidance.

Can I fill gaps between floorboards or weatherboards?

Not tongue-and-groove or weatherboard gaps. The sheet points to No More Gaps Exterior for those applications.

How much does a cartridge cover?

The 475g technical-sheet cartridge gives about 10.4m of a 6mm bead; application and joint size affect use.

Can it stay constantly damp?

No. Permanent immersion and constantly damp areas are excluded.

What is the movement capability?

Up to 15% under ISO 9046. The separate +300% elongation-at-break figure is not a joint-movement allowance.

Does it need bare-finger tooling?

No. The technical sheet specifies a wet gloved finger or spatula.

What does the VOC certificate show?

12g/L, below the selected 50g/L category limit, from the named August 2023 test. It is not automatic project certification.

Can I use it outside?

Our product page and technical sheet differ on exterior use. This page is for interior applications; confirm an exterior job with our team first.

What should I know about suitable interior gaps?

Use for gaps and cracks around skirting boards, cornices, and the inside of window and door frames. The TDS lists plasterboard, wood, particleboard, cement sheeting, aluminium and glass.

How do I prepare, fill and finish?

Clean and dry the surfaces; remove dust and grease; Cut the nozzle at 45°, cut the cartridge tip, fit the nozzle and load the gun; Push the filler into the gap or joint with the caulking gun; Smooth with a wet, gloved finger or spatula; Remove wet excess with a damp cloth. Use a scraper for dry excess.

When to paint?

The application instructions give approximately 30 minutes for a skin to form before painting. This guidance is qualified for gaps no larger than 5 mm deep and 10 mm wide, at temperatures above 10°C. Let the filler dry before painting and avoid a thick paint coat.