Product
Product Facts
- Product Name
- Rapid Mould Killer 750mL
- Brand
- Selleys
- Category
- Home & Garden > Cleaning & Maintenance
Rapid Mould Killer 750ml
Selleys Rapid Mould Killer 750ml is a powerful solution for removing mould in larger areas. Keep your family safe and healthy with our fast and effective cleaner.
Check the pack details below, then find a retailer near you. Range and availability vary by store.
Key features
- Effectively eradicates stubborn mould
- Fast acting – destroys mould in 30 seconds
- Eliminates 99.9% of germs

Product details
| Can be used in | Bathrooms · Laundries · Mould-affected areas · Shower screens · Toilets · Laundry surfaces · Plastic · Shower curtains · Rubber bath mats |
|---|
Follow the use and care instructions below for Rapid Mould Killer 750ml. Check the exact pack for any additional directions.
How to use
- Twist nozzle to SPRAY or STREAM.
- Spot test first.
- Spray, leave for 30 seconds then rinse, wipe or scrub off.
Source: Our product directions.
Technical details
| Can be used in |
Bathrooms Laundries Mould-affected areas Shower screens Toilets Laundry surfaces Plastic Shower curtains Rubber bath mats |
Source: Our product directions.
Limitations
- On some matt finish tiles or hard water areas staining may occur; patch test first
- Not suitable for fabric, mirror tiles, metallic surfaces, older baths or basins
- Do not mix with other cleaners
Source: Our product directions.
Safety before you start
This Australian SDS is for the formulation supplied from April 2025. Match the product code on your pack; ask our team for the relevant earlier sheet if you have older stock.
RAPID MOULD KILLER 750ML From April 2025
SDS signal word: Danger.
- Causes skin irritation. (H315)
- Causes serious eye damage. (H318)
Handling: Avoid eye contact and skin contact. Avoid inhalation of vapour, mist or aerosols.
Protective equipment and ventilation
Wear safety shoes, overalls, gloves, chemical goggles. Available information suggests that gloves made from nitrile rubber should be suitable for intermittent contact. However, due to variations in glove construction and local conditions, the user should make a final assessment. Always wash hands before smoking, eating, drinking or using the toilet. Wash contaminated clothing and other protective equipment before storing or re-using.
Ventilation: Ensure ventilation is adequate to maintain air concentrations below Exposure Standards. Use only in well ventilated areas. Use with local exhaust ventilation or while wearing appropriate respirator. Vapour heavier than air - prevent concentration in hollows or sumps. Do NOT enter confined spaces where vapour may have collected.
Australian safety data sheet · issued 18 March 2025 · sections 2, 7 and 8. Read the full SDS for first aid, spill response, incompatibilities and disposal.
Storage precautions
Store in a cool, dry, well-ventilated place and out of direct sunlight. Store away from foodstuffs. Store away from incompatible materials described in Section 10. Store away from sources of heat and/or ignition. Keep container standing upright. Keep containers closed when not in use - check regularly for leaks.
RAPID MOULD KILLER 750ML (From April 2025): storage and product data
Store between jobs
Store in a cool, dry, well-ventilated place and out of direct sunlight. Store away from foodstuffs. Store away from incompatible materials described in Section 10. Store away from sources of heat and/or ignition. Keep container standing upright. Keep containers closed when not in use - check regularly for leaks.
This material is a Scheduled Poison Schedule 5 (Caution) and must be stored, maintained and used in accordance with the relevant regulations.
| Form | Liquid |
|---|---|
| Colour | Colourless |
| Odour | Chlorine |
| Solubility | Soluble in water |
| Specific Gravity | 1.07 |
| Relative Vapour Density (air=1) | >1 |
| Vapour Pressure | N Av |
| Flash Point (°C) | N App |
| Explosion/Flammability Limits | N App |
| Autoignition Temperature (°C) | N Av |
| Melting Point/Range (°C) | N Av |
| Boiling Point/Range (°C) | Approx. 100 |
| pH | >11 |
| Viscosity | 100 - 150cP |
| Total VOC (g/Litre) | N Av |
Others in this range
Alongside this product:
Browse from here
Where this page sits:
- Mould Removal & Mould Cleaners
- Home Cleaning Products & Cleaning Supplies
- Adhesives, Fillers, Sealants & More
- All Products
- Discover Selleys Product Brands
- Find a product
Elsewhere in this category
Nearby products and groups:
- Bathroom Cleaning Products
- BBQ Grease & Grime Cleaner
- BBQ Tough Clean
- BBQ Tough Wipes
- Best BBQ Grill & Plate Cleaners & BBQ Degreaser
- Best Cleaning Cloths & Multi Purpose Cleaning Cloths
- Complete Clean Bathroom & Shower Spray
- Complete Clean Glass & Mirror Spray
- Complete Clean Multi Purpose Spray
- Complete Clean Multi-Surface Floor Cleaner
- Complete Clean Multipurpose Disinfectant Cleaning Wipes
- Complete Clean Power Gel Drain Cleaner
- Complete Clean Toilet Gel
- Dry Lubricant Spray & House Hold Lubricants
Typical values describe the material in this safety data sheet. They are not application instructions or performance guarantees. N Av means not available; N App means not applicable.
Ingredients disclosed in the SDS
CHEMICAL ENTITY CAS NO PROPORTION 1-Dodecanamine, N,N-dimethyl-, N-oxide 1643-20-5 1 - 10 % (w/w) Sodium hypochlorite 7681-52-9 1 - 10 % (w/w) Sodium lauryl ether sulfate 68585-34-2 1 - 10 % (w/w) Sodium hydroxide 1310-73-2 <1 % (w/w) Ingredients determined to be non-hazardous or below reporting limits Balance ____________ 100%
These are the ingredients disclosed for hazard communication, not the complete formulation. Use the application instructions to decide suitability for your project.
First aid from the matching SDS
If poisoning occurs, contact a doctor or Poisons Information Centre (Phone Australia 131 126, New Zealand 0800 764 766).
Inhalation: Remove victim from exposure - avoid becoming a casualty. Remove contaminated clothing and loosen remaining clothing. Allow patient to assume most comfortable position and keep warm. Keep at rest until fully recovered. Seek medical advice if effects persist.
Skin Contact: If skin or hair contact occurs, immediately remove contaminated clothing and flush skin and hair with running water. Continue flushing with water until advised to stop by the Poisons Information Centre or a Doctor; or for 15 minutes and transport to Doctor or Hospital.
Eye contact: Immediately irrigate with copious quantities of water for 15 minutes. Eyelids to be held open. Remove clothing if contaminated and wash skin. Urgently seek medical assistance. Transport to hospital or medical centre.
Ingestion: Rinse mouth with water. If swallowed, do NOT induce vomiting. Give a glass of water to drink. Never give anything by the mouth to an unconscious patient. If vomiting occurs give further water. Seek medical advice.
PPE for First Aiders: Wear safety shoes, overalls, gloves, chemical goggles. Available information suggests that gloves made from nitrile rubber should be suitable for intermittent contact. However, due to variations in glove construction and local conditions, the user should make a final assessment. Always wash hands before smoking, eating, drinking or using the toilet. Wash contaminated clothing and other protective equipment before storing or re-using.
Notes to physician: Treat symptomatically. Can cause corneal burns.
Disposal
Persons conducting disposal, recycling or reclamation activities should ensure that appropriate personal protection equipment is used, see "Section 8. Exposure Controls and Personal Protection" of this SDS. If possible material and its container should be recycled. If material or container cannot be recycled, dispose in accordance with local, regional, national and international Regulations.
Australian SDS · sections 1, 3, 4, 7, 9 and 13 · 18 March 2025
Technical and safety documents
Read our product directions together with the documents below. Check that each document matches the product and pack you’re using.
- Australian SDS — RAPID MOULD KILLER 750ML From April 2025 · 18 March 2025
Follow our product directions above. A separate technical manual is not available among the documents linked here.
Need a hand choosing the right document or checking your application? Contact our team with the product name, pack code, surfaces and intended use.
How long do I leave it on mould?
Spot test first. Spray, leave for 30 seconds, then rinse, wipe or scrub off. Follow the exact pack directions.
Which surfaces must I avoid?
Fabric, mirror tiles, metallic surfaces, older baths and basins. Spot test first because staining may occur on some matt-finish tiles or in hard-water areas.
Can I use it on a fabric shower curtain?
No. Although shower curtains are listed as a use, fabric is specifically excluded.
Can I mix it with another cleaner?
No. Do not mix with other cleaners.
Which 750mL formulation does this safety information cover?
The formulation from April 2025, codes 101280M and 102180MNZ, barcode 9300697127747. Ask our team for the earlier SDS if you have older stock or cannot identify the formulation.
What precautions should I take?
Danger: causes skin irritation and serious eye damage. Avoid skin/eye contact and inhalation. Use the SDS protective equipment, including chemical goggles, and ventilation controls. Read the full sheet before use.
Does the 99.9% claim identify particular organisms?
Check your exact pack or ask our team to confirm the organisms and disinfecting conditions for your formulation. The 30-second mould-removal directions should not be extended to an unsupported germ-specific claim.
Where is the matching SDS?
Australian SDS SELGHSEN001675, version 1.0, 18 March 2025, for the 750mL formulation from April 2025: https://go.lupinsys.com/duluxgroup/harms/public/materials/bd6f7b27cdfb7b181b03b76ccaa7389f-published/attachments_api/952433882bcb18c2d28fa7bd30918093/search_api/RAPID_MOULD_KILLER_750ML__From_April_2025_-AUS_GHS.pdf
Where can I buy it?
Use our store finder: https://www.selleys.com.au/find-a-store/ .
What are the limitations?
On some matt finish tiles or hard water areas staining may occur; patch test first; Not suitable for fabric, mirror tiles, metallic surfaces, older baths or basins; Do not mix with other cleaners.
What should I know about safety before I start?
This Australian SDS is for the formulation supplied from April 2025. Match the product code on your pack; ask our team for the relevant earlier sheet if you have older stock. Handling: Avoid eye contact and skin contact. Avoid inhalation of vapour, mist or aerosols.
Which technical and safety documents are available?
Read our product directions together with the documents below. Check that each document matches the product and pack you’re using. Follow our product directions above. A separate technical manual is not available among the documents linked here. Need a hand choosing the right document or checking your application?