Selleys Liquid Nails: Professional Construction Adhesives
Compare the products below with your materials, conditions and the finish you need.
Selleys Liquid Nails construction adhesives
The Liquid Nails range includes general construction, high-grab, flexible and project-specific adhesives. Match the product to the materials, exposure and required installation method.
Explore the range
- Liquid Nails Rapid Cure
- Liquid Nails Fast Grab
- Liquid Nails Extreme Grab
- Liquid Nails Mirror Metal
- Liquid Nails Exterior
- Liquid Nails Heavy Duty
- Liquid Nails Clear
- Liquid Nails Construction Adhesive
- Liquid Nails Flex
- Liquid Nails Landscape — see the product’s masonry and retaining-wall limitations.
Define the bond before choosing the adhesive
Name both materials and any paint, coating, laminate or backing film. Decide whether each surface is porous, whether the joint has gaps, and whether it will face load, vibration, movement, weather, water or heat. A product that works on one timber-to-masonry joint may not be suitable for a mirror, flexible plastic, coated metal or continuously wet application.
Compare working time, repositioning time, initial grab, required bead pattern, temporary support and full cure. A fast-grab or rapid-setting statement does not mean immediate full strength. Heavy, stressed and overhead work may require support or mechanical fixing even when the adhesive has a high initial grab.
Prepare and assemble the joint
- Confirm the product covers both substrates and the service conditions.
- Remove dust, grease, moisture, loose coatings and release contamination as directed.
- Dry-fit the parts and plan supports before applying adhesive.
- Apply the stated bead, spread or contact method and assemble within the working time.
- Maintain support and avoid loading until the relevant cure instruction is satisfied.
Read limitations before application
Check excluded plastics, mirrors, polystyrene, permanent immersion, structural use and temperature limits on the exact product. Use the current pack label, Technical Data Sheet and Australian Safety Data Sheet. Where two manufacturer sources disagree, keep both values visible and ask which applies to the supplied formulation.
Compare the installation method as well as the materials
Two construction adhesives may cover similar substrates but require different bead patterns, support periods and moisture conditions. Decide whether the job needs fast initial grab, extra repositioning time, flexibility, a clear finish, exterior exposure or a specialist mirror-compatible formulation. Then open the matching product page and check the full method.
Plan supports before applying the adhesive. Treat product-specific support times as conditional milestones rather than full-cure promises, and use mechanical fixings where the instructions or load require them. For mirrors, follow the specialist bead spacing, backing compatibility and perimeter-sealing sequence rather than substituting a general construction adhesive.
What to check for your job
- No. The TDS lists 24 hours for full cure, subject to temperature, humidity and material porosity. Its short initial-setting claim must not be presented as full cure. On porous surfaces, temporary clamps can typically be removed after 15–20 minutes; heavier items and adverse conditions need longer.
- Follow the particular product instructions. Original needs at least 24 hours of support; Heavy Duty normally eight hours on porous surfaces; Exterior at least four hours on porous surfaces. These are conditional support times, not full-cure promises. High-stress work requires mechanical fixings.
- No. Fast Grab requires support for heavy or overhead items and at least 24 hours before removing temporary supports, longer where required. Extreme Grab requires support above 5 kg and for all overhead applications; its claimed grab strength is not an individual joint safe working load.
- It is elongation at break under the stated test, not a rated 400% joint movement capability. Check the Flex product page for substrate exclusions, support and curing instructions.
- Exterior and Flex have outdoor applications. Fast Grab is limited by its TDS to interior and sheltered exterior locations protected from moisture. Check each product’s limitations; an exterior claim does not permit permanent immersion.
- Use the Mirror & Metal product instructions. The TDS normally calls for 72-hour support, separated beads and at least one week before perimeter sealing. Mirror thickness, backing and substrate conditions matter; Original is not for mirrors.
- Our retail pages and TDS differ for some formulations, including Original, Exterior, Heavy Duty and Mirror & Metal. Individual product pages identify the competing statements. Check the cartridge and ask Selleys which document applies rather than combining the numbers.
Compare the options: Selleys Liquid Nails: Professional Construction Adhesives
Use this category to create a shortlist, then compare the exact candidates in a simple job table. Record the materials, location, exposure, movement or load, required finish, working time, support or protection period, full cure and major exclusions. A shared category or brand name does not make the products interchangeable.
- Suitability: both substrates, coatings and service conditions.
- Application: preparation, tools, dimensions, coverage and working time.
- Waiting: support removal, water exposure, sanding, painting and full cure.
- Finish: colour, visibility, flexibility, paintability and clean-up.
- Evidence: the current pack, Technical Data Sheet and Australian Safety Data Sheet.
Open the individual page for every shortlisted product. Where this category contains a retained discontinued page, use it to identify older stock or work and confirm current availability or a replacement directly with us.
Complete bond-planning checklist for Selleys Liquid Nails: Professional Construction Adhesives
Write down both substrates, including paint, coatings, laminates, backing films and whether each surface is porous. Define the joint gap, load direction, vibration, movement, water, weather, heat and required finish. These details decide whether the named product is suitable and whether temporary support or permanent mechanical fixing is required.
- Confirm both materials and every surface treatment are listed or otherwise covered by the current instructions.
- Separate working time, repositioning time, initial grab, support-removal time and full cure.
- Dry-fit the parts and prepare clamps, braces or fixings before opening the product.
- Follow the stated bead, spread, contact or assembly method.
- Keep the joint unloaded and within the specified conditions until the relevant cure milestone.
Do not transfer a strength, grab or cure claim from another formulation in the same range. Mirrors, flexible plastics, polystyrene, continuously wet areas, overhead work and structural loads require explicit product coverage.
More help for your project
Use these pages to compare the exact product, method or application that follows from Selleys Liquid Nails: Professional Construction Adhesives. A related page is a route into more specific information, not evidence that every product is interchangeable.
- Liquid Nails Construction Adhesive — Seven days to full strength is the figure that should shape your sequencing. The joint will hold itself together long before that, but it keeps gaining strength for a week.
- How To Remove Dried Liquid Nails — In this answer, we apply our product guidance to the materials and conditions in this question.
- Can You Paint Over Liquid Nails? — Two of the three products on this page carry the signal word Danger for different reasons, and the sequencing advice above puts each hazard in a specific slot.
- Painting Liquid Nails Clear — Paint Liquid Nails Clear only when fully cured. Current product directions specify 7 days for full cure and maximum strength; do not use the old minimum-24-hour answer as a universal paint time.
- Best Construction Adhesives & Glues — Construction adhesives are the products that fix building materials to each other — panels, mouldings, trim, fixtures, pavers and roof tiles — where nails or screws would be impractical, ugly or impossible.
- Selleys Adhesives: Glue, Contact & Construction Solutions — The range is designed with specific uses in mind, and that choice of use also affects cure time.
- Selleys Liquid Nails Clear — The 5°C to 35°C application range is the constraint most people ignore.
- Selleys Liquid Nails Exterior — Follow the current cartridge instructions and the matching TDS. Remove dust, grease and pooled water; assemble the bead pattern promptly and use sufficient supports.
Product instructions and safety sheets
Ready to choose a product? Use the links below for the products featured on this page. Check the exact product, pack and application before you start. Each product has its own directions and limitations.
- Liquid Nails Flex — product details and pack options
- Liquid Nails Exterior — product details and pack options
- Liquid Nails Construction Adhesive — product details and pack options
- Liquid Nails Heavy Duty — product details and pack options
- Liquid Nails Fast Grab — product details and pack options
- Liquid Nails Extreme Grab — product details and pack options
- Liquid Nails Rapid Cure — product details and pack options
- Liquid Nails Landscape — product details and pack options
- Liquid Nails Mirror & Metal — product details and pack options
- Liquid Nails Clear — product details and pack options
For any missing technical or safety document, contact our team with the exact product name and pack code.
Need help matching a document or checking your job? Contact our team. You can also find a store.
Does the Flex 400% figure mean a joint can move 400%?
No. The technical sheet identifies 400% as elongation at break. It is not a joint-movement design allowance.
Does high initial grab remove every need for supports or fasteners?
No. Follow the exact product’s load, support and cure instructions; high-stress applications may need mechanical fasteners.
Can one Liquid Nails product bond every building material?
No. Match the exact product to both materials and the service conditions, and observe its exclusions.
How do I define the bond before choosing the adhesive?
Name both materials and any paint, coating, laminate or backing film. Decide whether each surface is porous, whether the joint has gaps, and whether it will face load, vibration, movement, weather, water or heat. A product that works on one timber-to-masonry joint may not be suitable for a mirror, flexible plastic, coated metal or continuously wet application.
How do I prepare and assemble the joint?
Confirm the product covers both substrates and the service conditions; Remove dust, grease, moisture, loose coatings and release contamination as directed; Dry-fit the parts and plan supports before applying adhesive; Apply the stated bead, spread or contact method and assemble within the working time; Maintain support and avoid loading until the relevant cure instruction is satisfied.
How do I read limitations before application?
Check excluded plastics, mirrors, polystyrene, permanent immersion, structural use and temperature limits on the exact product. Use the current pack label, Technical Data Sheet and Australian Safety Data Sheet. Where two manufacturer sources disagree, keep both values visible and ask which applies to the supplied formulation.
How do I compare the installation method as well as the materials?
Two construction adhesives may cover similar substrates but require different bead patterns, support periods and moisture conditions. Decide whether the job needs fast initial grab, extra repositioning time, flexibility, a clear finish, exterior exposure or a specialist mirror-compatible formulation. Then open the matching product page and check the full method.
What should I check for my job?
No. The TDS lists 24 hours for full cure, subject to temperature, humidity and material porosity. Its short initial-setting claim must not be presented as full cure. On porous surfaces, temporary clamps can typically be removed after 15–20 minutes; heavier items and adverse conditions need longer; Follow the particular product instructions. Original needs at least 24 hours of support; Heavy Duty normally eight hours on porous surfaces; Exterior at least four hours on porous surfaces. These are conditional support times, not full-cure promises. High-stress work requires mechanical fixings.
How do I compare the options?
Use this category to create a shortlist, then compare the exact candidates in a simple job table. Record the materials, location, exposure, movement or load, required finish, working time, support or protection period, full cure and major exclusions. A shared category or brand name does not make the products interchangeable.
What should I know about complete bond-planning checklist for Selleys Liquid Nails?
Write down both substrates, including paint, coatings, laminates, backing films and whether each surface is porous. Define the joint gap, load direction, vibration, movement, water, weather, heat and required finish. These details decide whether the named product is suitable and whether temporary support or permanent mechanical fixing is required.
Which instructions and safety sheets cover this product?
Ready to choose a product? Use the links below for the products featured on this page. Check the exact product, pack and application before you start. Each product has its own directions and limitations. For any missing technical or safety document, contact our team with the exact product name and pack code.
Does Rapid Cure fully cure in ten minutes?
No. The TDS lists 24 hours for full cure, subject to temperature, humidity and material porosity. Its short initial-setting claim must not be presented as full cure. On porous surfaces, temporary clamps can typically be removed after 15–20 minutes; heavier items and adverse conditions need longer.