Product

Product Facts

Product Name
Liquid Nails Landscape
Brand
Selleys
Category
Home & Garden > Construction Adhesives

Liquid Nails Landscape

Get the perfect adhesive for your outdoor projects with Selleys Liquid Nails Landscape. Perfect for rocks, stones, and more.

Check the pack details below, then find a retailer near you. Range and availability vary by store.

Liquid Nails Landscape — product image

Product details

Pack, technology and materials
ColourBeige
TechnologySolvent-based

Liquid Nails Landscape: technical details

Technical data · page 1
PackagingSizeColour
Cartridge300 gramsGrey
Technical data · page 1
PropertyTypical Result
TechnologyNeutral Cure Silicone
ColourGrey
Specific Gravity @ 25°C~1.35
Skin Time10-15 minutes
Cure Rate2mm / 24hrs
Tack Free Time35 ± 5 minutes
Slump< 0.1 inch
Shore A Hardness~30
Elongation at Break>300%
Indicative data only, not intended for preparation of specifications

What it does

  • High Strength
  • Flexibility
  • Superior Weather Resistance
  • Shock Proof Bond

Conditions and compatibility

  • Not for permanent water immersion
  • Cannot be painted over. Safety Directions Warning: Causes eye irritation
  • Keep out of reach of children.
  • Read label before use
  • Avoid skin and eye contact and breathing vapours
  • Wash all exposed skin thoroughly after handling
  • Cure product before disposal
  • Product releases methyl ethyl ketoxime during cure

Technical data sheet · : 23/11/2020

Where to use it

Liquid Nails® Landscape is suitable for use on materials such as stone, concrete, capstones, terracotta and timber and it is ideal for landscaping projects such as:

  • Stabilising stone & interlocking masonry retailing walls
  • Bonding pavers to concrete
  • Bonding capstones to walls
  • Repairing rockeries
  • Sealing between treated pine logs to reduce soil loss
  • Stabilising loose stone steps.

Source: Technical data sheet, page 1.

Prepare the surface

  • Ensure the surface is sound, dry and free from oil, grease and loose powdery material (if necessary, use mineral turpentine to clean surface and allow to dry.
  • Cut cartridge tip, fit nozzle and cut nozzle to a suitable size opening (approximately 5mm).
  • Apply using caulking gun

Source: Technical data sheet, page 1.

How to apply

  • Apply ‘dobs’ or ‘beads; of adhesive of appropriate thickness to ensure sufficient contact and spread between both surfaces. (To minimise ‘squeeze out’ apply at least 12mm in from edges).
  • Immediately bring surfaces together before product skins (within 5 minutes) and apply sufficient pressure to spread adhesive between both surfaces
  • Do not wipe excess ‘squeeze out’. Wait until product cures and remove by trimming with a sharp blade but avoid cutting into bond.
  • Leave undisturbed until adhesive cures sufficiently. Do not allow traffic on stairs or use walls for at least 24 hours. Note
  • Not for soft or crumbly materials.
  • If repositioning materials, fresh adhesive must be applied to achieve bonding.
  • Do not use as the sole bonding agent for structural bonding

Source: Technical data sheet, page 1.

Application tips

Spilt or smeared adhesive is best left to cure and then remove by abrasion.

Source: Technical data sheet, page 1.

Clean up

Uncured product may be removed with mineral turpentine. Cured product can be removed with the help of Selleys Silicone Remover or by mechanical action.

Source: Technical data sheet, page 1.

Storage

  • Store in a cool, dry, well-ventilated place and out of direct sunlight
  • Store away from foodstuffs.

Source: Technical data sheet, page 1.

Where not to use it

  • Not for permanent water immersion
  • Cannot be painted over. Safety Directions Warning: Causes eye irritation
  • Keep out of reach of children.
  • Read label before use
  • Avoid skin and eye contact and breathing vapours
  • Wash all exposed skin thoroughly after handling
  • Cure product before disposal
  • Product releases methyl ethyl ketoxime during cure

Source: Technical data sheet, page 2.

Safety before you start

Check the product name on your pack against the Australian SDS below before use.

SELLEYS LIQUID NAILS LANDSCAPE

SDS signal word: Danger.

Handling: Avoid eye contact and skin contact. Avoid inhalation of dust.

Protective equipment and ventilation

Wear safety shoes, overalls, gloves, safety glasses. Available information suggests that gloves made from nitrile rubber should be suitable for intermittent contact. However, due to variations in glove construction and local conditions, the user should make a final assessment. Always wash hands before smoking, eating, drinking or using the toilet. Wash contaminated clothing and other protective equipment before storing or re-using.

Ventilation: Natural ventilation should be adequate under normal use conditions.

Australian safety data sheet · issued 16 November 2023 · sections 2, 7 and 8. Read the full SDS for first aid, spill response, incompatibilities and disposal.

SELLEYS LIQUID NAILS LANDSCAPE: storage and product data

Store between jobs

Store in a cool, dry, well-ventilated place and out of direct sunlight. Store away from foodstuffs. Store away from incompatible materials described in Section 10. Store away from sources of heat and/or ignition. Keep container standing upright. Keep containers closed when not in use - check regularly for spills.

Classified as a C1 (COMBUSTIBLE LIQUID) for the purpose of storage and handling, in accordance with the requirements of AS 1940. Refer to State Regulations for storage and transport requirements.

Typical physical properties from this SDS
FormPaste
ColourGrey
OdourCharacteristic
SolubilityInsoluble in water
Specific Gravity1.42
Relative Vapour Density (air=1)>1
Vapour PressureN Av
Flash Point (°C)77
Flammability Limits (%)N App
Autoignition Temperature (°C)N Av
Melting Point/Range (°C)N Av
Boiling Point/Range (°C)N Av
pHN Av
ViscosityN Av
Total VOC (g/Litre)N Av

Others in this range

Alongside this product:

Browse from here

Where this page sits:

Typical values describe the material in this safety data sheet. They are not application instructions or performance guarantees. N Av means not available; N App means not applicable.

Ingredients disclosed in the SDS
CHEMICAL ENTITY CAS NO PROPORTION
2-Butanone, O,O',O''-(methylsilylidyne)trioxime 22984-54-9 1 - 10 % (w/w)
2-Butanone, O,O',O''-(ethenylsilylidyne)trioxime 2224-33-1 1 - 10 % (w/v)
Methyl ethyl ketoxime 96-29-7 <1 % (w/w)
N-[3-(Trimethoxysilyl)propyl]ethylenediamine 1760-24-3 <1 % (w/w)
Ingredients determined to be non-hazardous or below reporting limits Balance
____________
100%

These are the ingredients disclosed for hazard communication, not the complete formulation. Use the application instructions to decide suitability for your project.

First aid from the matching SDS

If poisoning occurs, contact a doctor or Poisons Information Centre (Phone Australia 131 126, New Zealand 0800 764 766).

Inhalation: Remove victim from exposure - avoid becoming a casualty. Remove contaminated clothing and loosen remaining clothing. Allow patient to assume most comfortable position and keep warm. Keep at rest until fully recovered. Seek medical advice if effects persist.

Skin Contact: Effects may be delayed. If skin or hair contact occurs, remove contaminated clothing and flush skin and hair with running water. If swelling, redness, blistering or irritation occurs seek medical assistance. For gross contamination, immediately drench with water and remove clothing. Continue to flush skin and hair with plenty of water (and soap if material is insoluble). For skin burns, cover with a clean, dry dressing until medical help is available. If blistering occurs, do NOT break blisters. If swelling, redness, blistering, or irritation occurs seek medical assistance.

Eye contact: Immediately irrigate with copious quantities of water for 15 minutes. Eyelids to be held open. Remove clothing if contaminated and wash skin. Urgently seek medical assistance. Transport to hospital or medical centre.

Ingestion: Rinse mouth with water. If swallowed, do NOT induce vomiting. Give a glass of water to drink. Never give anything by the mouth to an unconscious patient. If vomiting occurs give further water. Seek medical advice.

PPE for First Aiders: Wear safety shoes, overalls, gloves, safety glasses. Available information suggests that gloves made from nitrile rubber should be suitable for intermittent contact. However, due to variations in glove construction and local conditions, the user should make a final assessment. Always wash hands before smoking, eating, drinking or using the toilet. Wash contaminated clothing and other protective equipment before storing or re-using.

Notes to physician: Treat symptomatically. Effects may be delayed. Can cause corneal burns.

Disposal

Persons conducting disposal, recycling or reclamation activities should ensure that appropriate personal protection equipment is used, see "Section 8. Exposure Controls and Personal Protection" of this SDS. If possible material and its container should be recycled. If material or container cannot be recycled, dispose in accordance with local, regional, national and international Regulations.

Australian SDS · sections 1, 3, 4, 7, 9 and 13 · 16 November 2023

Technical and safety documents

The technical data sheet covers application and performance conditions. The safety data sheet covers hazards and safe handling. Use both alongside the pack instructions.

Need a hand choosing the right document or checking your application? Contact our team with the product name, pack code, surfaces and intended use.

Which cartridge and colour should I expect?

Our online page lists 415 g and beige; the technical sheet lists 300 g and grey, while the SDS identifies 415 g and grey. Check the physical pack and contact our team before purchase or colour-critical use. These differences do not prove separate formulations.

Can I paint it?

Do not plan a painted finish without confirmation for your exact cartridge. The technical sheet says it cannot be painted over, although our online page says paintable when fully cured.

Is it a silicone or solvent-based adhesive?

The technical sheet calls it a neutral-cure silicone; the online page says solvent-based. Contact our team with your cartridge code to confirm the matching instructions before choosing it for chemistry-sensitive work.

What can I use it for?

The technical sheet lists suitable stone, concrete, capstones, terracotta and timber for pavers, capstones, rockeries, treated-pine log sealing, loose stone steps and stone or interlocking masonry retaining walls. Confirm the exact cartridge and application first; do not use it as the sole structural bonding agent.

Can I immerse the finished bond?

No. The technical sheet excludes permanent water immersion. The online reference to avoiding immersion before cure is not permission for permanent immersion afterwards.

How quickly must I assemble the parts?

Use the 23 November 2020 technical sheet’s 300 g neutral-cure silicone method only after our team confirms that it applies to your current cartridge. The technical-sheet method says immediately, within five minutes and before skinning, with enough pressure to spread the adhesive. Its 10–15-minute skin time does not extend that instruction. The online five-minute holding direction is different; confirm the method for your pack.

Can I reposition the materials?

Use the 23 November 2020 technical sheet’s 300 g neutral-cure silicone method only after our team confirms that it applies to your current cartridge. The technical sheet requires fresh adhesive if repositioning, to achieve bonding.

How close to the edge should I apply it?

Use the 23 November 2020 technical sheet’s 300 g neutral-cure silicone method only after our team confirms that it applies to your current cartridge. The technical sheet says to keep dobs or beads at least 12 mm in from edges to minimise squeeze-out, with enough thickness for contact and spread between both surfaces.

When can I use stairs or walls?

Use the 23 November 2020 technical sheet’s 300 g neutral-cure silicone method only after our team confirms that it applies to your current cartridge. The technical sheet says at least 24 hours and sufficient cure, with a cure rate of 2 mm per 24 hours. Our online page gives seven days to full strength. Confirm the loading schedule for your joint; the minimum wait is not full cure for every thickness.

Should I wipe away squeeze-out?

Use the 23 November 2020 technical sheet’s 300 g neutral-cure silicone method only after our team confirms that it applies to your current cartridge. Confirm the cleanup method before applying. The technical sheet says not to wipe squeeze-out: let it cure, then trim without cutting into the bond. The online directions say to remove excess before it sets. Do not combine these instructions.

What are the important safety hazards?

The Australian SDS uses Danger: combustible liquid, may cause an allergic skin reaction and causes serious eye damage. Eye contact can cause corneal burns and permanent injury. Follow its PPE and full urgent first-aid response.

What temperatures apply?

The online page lists application 5°C to 35°C and service −20°C to 100°C. Confirm these for your exact cartridge with our team before temperature-critical use; do not combine them with unconfirmed pack or chemistry details.